Nothing drags down the start of the day like a shower that barely gets going. Low water pressure can seem like a serious headache, but more often than not, it’s something simple. The job is working out where the trouble actually starts.
Is it the whole house, or one tap?
Start simple. If it’s just one tap or the shower barely gets going, look right there first. The usual suspects: a blocked aerator on the tap, a shower head clogged with limescale, or a tired old valve. We see these all the time. But if every tap in the place is struggling, bath, basin, kitchen, all of them, then it’s not just the one fitting. You’re likely looking at something further back, maybe the main supply or a problem somewhere in the pipework lurking behind walls or under floors.
Check both hot and cold taps on their own. If the cold runs well but the hot barely does, that points to the boiler, the hot water cylinder or something in the airing cupboard. Not the stopcock or the supply coming in.
Pressure dropping at certain times? Make a note of when it happens. If it’s always slow first thing or at tea time, but fine when everyone’s out, the main in the street is likely flat out. Nothing wrong at your end.
The simple checks for low water pressure
- Make sure the stopcock is fully open; it's often half closed after earlier work.
- Unscrew tap aerators and soak them in descaler.
- Descale or replace a tired showerhead.
- Ask a neighbour whether their pressure has dropped too.
- Check your water supplier's website for local work.
When the pipes are the problem
Old pipework can be a real culprit for low water pressure. In a lot of older houses, you'll still find narrow pipes, plenty of corrosion, or even original lead supply pipes running in from the street. Over time, limescale and rust build up inside, choking the flow to a trickle. Swap out the main supply or those key stretches inside, and the difference at the taps can be night and day.
Plastic and copper last well if they've been put in properly. Planning any work with floorboards up? That's the time to fit decent-sized pipes for the runs that feed your bath, shower and kitchen. It's not costly and does the job right across the house.
You’ll usually find any remaining lead pipe near the stopcock under the sink or by the front door. It looks dull grey, feels soft if you scratch it with a key, and the joints are round and swollen. Not sure? Any decent plumber will take one look and know.
When it's the supply
You can’t always count on mains pressure to deliver a decent flow. If your house is halfway up a hill or right at the end of a long lane, you’ll know about it. The water company will tell you the usual pressure for your postcode and let you know if there’s a problem on their network. If the neighbours’ taps are slow too, give them a ring.
They’ll check the pressure at the stop tap by the pavement or your front gate. If the reading’s strong there and your kitchen tap still barely trickles, that’s for your plumber, not theirs. But if it’s feeble at the boundary, it’s over to the water company.
Pressure indoors can still let you down even if the boundary’s fine. We see it a lot in bigger homes, or anywhere with two bathrooms. The flow often tails off if two showers or taps are running together. That’s where a pump or a booster tank earns its keep.
Sort out what’s holding things up before you start thinking about a pump. No point trying to push water through a stopcock that barely opens.
Pumps, boosters and accumulators
A shower pump takes water from your storage tank and sends it to the shower, or sometimes the whole bathroom. Mains boosters and accumulators come in when the water from the street just can't keep up. They store water under pressure, so you can run several taps at once without everything dropping to a dribble. The right bit of kit depends on whether your setup has cold water tanks in the loft or if everything comes straight off the mains.
Pumps make a racket. Put one under the bath or in the airing cupboard, and you'll hear it through the wall. The better installers use anti-vibration pads and find somewhere it won't drive you mad every morning.
You can't just fit a pump anywhere. There are strict limits on boosting water straight from the mains, so this isn't one to bodge. You'll need a plumber who knows the rules.
A hidden leak can drop the pressure
A leak in the supply pipe often shows up as low pressure at the taps and a nasty surprise on your bill. Pressure that drops overnight or all of a sudden? Try the water meter test: switch off every tap and appliance, then watch the meter. If it keeps ticking, there’s a leak somewhere. Time to ring a plumber or a leak detection firm.
Pressure that's too high
It sounds odd, but water pressure that's too high brings its own set of headaches. You'll get banging pipes, taps that drip, and fittings under strain. Sometimes the pipes shudder when you turn a tap off, or water spits from the spout. That's your cue to get a plumber round with a pressure gauge.
If the pressure's up where it shouldn't be, fitting a pressure reducing valve on the mains supply sorts it out. This one's straightforward and usually done in under an hour. You'll avoid bigger trouble later on.
High or low, a plumber with the right kit can find the answer fast. Saves a lot of guesswork.
Our view
Check if it's just the kitchen tap or the whole house playing up. Try the simple things first, see if someone's left the stopcock half shut, or if the cold tank in the loft's low. No sense paying for a plumber until you've done those. If your pipework's seen better days, or the mains can't keep up, a decent plumber should spot it and put it right. Not just flog you the latest gadget for the sake of it.


